Updated anvil-configure-host to enable connection.autoconnect.

This closes issue #576

Signed-off-by: digimer <mkelly@alteeve.ca>

share/words.xml

@@ -2722,6 +2722,7 @@ The file: [#!variable!file!#] needs to be updated. The difference is:
 		<key name="log_0839">Drive: [#!variable!device_name!#], IOs currently in progress: [#!variable!in_progress!#], weighted time spent: [#!variable!weighted_time_spent!# sec].</key>
 		<key name="log_0840">CPU percent time doing; (IO wait / user / system / nice'd / idle / involuntary wait): [#!variable!iowait!# / #!variable!user!# / #!variable!system!# / #!variable!nice!# / #!variable!idle!#/ #!variable!steal!#].</key>
 		<key name="log_0841">Processes; (total / running / blocked / IRQ interrupts): [#!variable!total!# / #!variable!running!# / #!variable!blocked!# / #!variable!interrupts!#].</key>
+		<key name="log_0842">Starting the network manager connection: [#!variable!id!#] (uuid: [#!variable!uuid!#]).</key>
 
 		<!-- Messages for users (less technical than log entries), though sometimes used for logs, too. -->
 		<key name="message_0001">The host name: [#!variable!target!#] does not resolve to an IP address.</key>

tools/anvil-configure-host

@@ -1767,6 +1767,7 @@ sub reconfigure_interfaces
 		   $general_ip_iface       = "" if $general_ip_iface eq "--";
 		my $device_type            = $anvil->data->{nmcli}{uuid}{$uuid}{'connection.type'}        // "";
 		my $match_interface_name   = $anvil->data->{nmcli}{uuid}{$uuid}{'match.interface-name'}   // "";
+		my $connection_autoconnect = $anvil->data->{nmcli}{uuid}{$uuid}{'connection.autoconnect'} // "";
 		my $active                 = $anvil->data->{nmcli}{uuid}{$uuid}{active};
 		$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { 
 			's1:uuid'                   => $uuid,
@@ -1774,12 +1775,28 @@ sub reconfigure_interfaces
 			's3:general_ip_iface'       => $general_ip_iface, 
 			's4:device_type'            => $device_type, 
 			's5:match_interface_name'   => $match_interface_name, 
-			's6:active'                    => $active, 
+			's6:connection_autoconnect' => $connection_autoconnect, 
+			's7:active'                 => $active, 
 		}});
 		
+		### NOTE: I don't think this is needed, but here's the code in case we change our mind.
+		if (0)
+		{
 			# Try activating it.
 			if ((not $general_ip_iface) && (not $active))
 			{
+				$anvil->Log->entry({source => $THIS_FILE, line => __LINE__, level => 1, 'print' => 1, key => "log_0842", variables => { 
+					id   => $connection_id,
+					uuid => $uuid, 
+				}});
+				
+				my $shell_call = $anvil->data->{path}{exe}{nmcli}." connection up ".$uuid;
+				$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { shell_call => $shell_call }});
+				my ($output, $return_code) = $anvil->System->call({shell_call => $shell_call});
+				$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { 
+					output      => $output, 
+					return_code => $return_code, 
+				}});
 				
 				# Rescan.
 				$anvil->Job->update_progress({
@@ -1795,6 +1812,7 @@ sub reconfigure_interfaces
 				$anvil->Network->collect_data({debug => 2});
 			}
 		}
+	}
 	
 	my $local_host = $anvil->Get->short_host_name();
 	my $prefix     = $anvil->data->{config}{prefix};
@@ -1885,6 +1903,16 @@ sub reconfigure_interfaces
 					$configure_link1 = 1;
 					$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { configure_link1 => $configure_link1 }});
 				}
+				
+				# Make sure that the autoconnect is enabled.
+				if ($anvil->data->{nmcli}{uuid}{$link1_nm_uuid}{'connection.autoconnect'} ne "yes")
+				{
+					my ($output, $return_code) = $anvil->Network->modify_connection({debug => 2, uuid => $link1_nm_uuid, variable => "connection.autoconnect", value => "yes"});
+					$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { 
+						output      => $output,
+						return_code => $return_code, 
+					}});
+				}
 			}
 			else
 			{
@@ -1935,6 +1963,16 @@ sub reconfigure_interfaces
 						$configure_link2 = 1;
 						$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { configure_link1 => $configure_link1 }});
 					}
+				
+					# Make sure that the autoconnect is enabled.
+					if ($anvil->data->{nmcli}{uuid}{$link2_nm_uuid}{'connection.autoconnect'} ne "yes")
+					{
+						my ($output, $return_code) = $anvil->Network->modify_connection({debug => 2, uuid => $link2_nm_uuid, variable => "connection.autoconnect", value => "yes"});
+						$anvil->Log->variables({source => $THIS_FILE, line => __LINE__, level => 2, list => { 
+							output      => $output,
+							return_code => $return_code, 
+						}});
+					}
 				}
 				else
 				{