* Fixed a bug in scan-drbd where the volume_uuid wasn't being stored in the proper hash, breaking insertions into scan_drbd_peers in some cases.
* Updated System->pids() to work with remote targets (will be used later to check for parallel runs of anvil-safe-start).
Signed-off-by: Digimer <digimer@alteeve.ca>
* The get_mmeory endpoint was completed.
* The get_replicated_storage endpoint was completed, though it requires testing and likely has issues.
To prepare for the get_status endpoint work, I needed to update ScanCore and modules to track the host_status. This commit contains the work needed for this.
* Updated ScanCore->post_scan_analysis_striker() to use configured fence devices (except PDUs) to check if a target host is off or on, in there is no host_ipmi interface. In all cases, if a machine can be confirmed on or off, the host_status is now updated.
* To support the above fence based power checks, updated scan-cluster to store the on-disk CIB in the new scan_cluster -> scan_cluster_cib colume.
* Updated ScanCore->parse_cib() to map stonith primitive IDs to fence agents. Updated ->parse_crm_mon() to not call if the executable doesn't exist to avoid unhelpful error messages in the logs when called from a Striker.
* Update DRBD->gather_data() to get the size data from /sys/block/drbd<minor>/size' x '/sys/block/drbd<minor>/queue/logical_block_size so it works when a device is Secondary (and can't be promoted).
* Updated Database->get_hosts_info() to record the short host name as well as the stored host name. Created ->update_host_status() as a wrapper to ->insert_or_update_hosts() that only updates the host status.
* Updated anvil-join-anvil to disabled ksm and ksmtuned daemons.
* Updated scancore and anvil-daemon to set the host_status to 'online' on startup.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug in ScanCore->agent_startup() where a (thankfully broken) check to append tables to the 'sys::database::check_tables' would cause an infinite loop as both were pointers to the same anonymous array.
* Fixed a bug in scan-ipmitool where the scan_ipmitool_variables table didn't use a host_uuid reference, causing resyncs of that table to sync for all hosts and cause DB errors when the scan_ipmitool record from another host wasn't sync'ed yet.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Database->_find_behind_databases() to not trigger a resync if the only difference in a table is the last-updated time and the difference is less than ten seconds. This should dramatically cut back on unnecessary resyncs and reduce load.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Finished scan-filesystems!
* Realized that filesystem UUIDs are not always actual UUIDs, and so created an additonal column in filesystems -> filesystem_internal_uuid and created a normal filesystem_uuid table.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Created Storage->parse_df that, shock!, parses 'df' output. Finished the long-ago started ->parse_lsblk as well.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug in Database->_find_behind_databases() _find_behind_databases() where the logic to figure out which column was the host_uuid reference was too liberal, causing the wrong column to be selected in some cases. Also added a check to not look for host_uuid columns on specific tables where a match would be made, but the column is allowed to be null (like server_host_uuid that indicates the host of the server).
* Started work on the scan-filesystems scan agent, which is needed to record the data that the file system UI endpoints will need.
* Removed the 'not null' constraint from 'servers' -> 'server_host_uuid'.
* Fixed a bug in 'anvil-provision-server' where the driver ISO being 'none' caused the provision script to use the driver ISO switch.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Cleaned up a log of logging to reduce the amount of log entries when running at log level 1.
* Bumped the scan-ipmitool default 'jump' range to 10c.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Reworked scan-ipimitool so that on nodes and dr hosts, it only scans itself. On strikers, it scans all hosts found in active Anvil! systems with a host_ipmi entry. `
* For all agents, reduced log verbosity to not push too much noise into anvil.log while scancore is running in the background.
Signed-off-by: Digimer <digimer@alteeve.ca>
Note: These changes below shouldn't have been in this branch... *sigh*
* Fixed an issue with tools/anvil-provision-server where a VM would be created but didn't boot. When this happens, an explicit boot is sent via virsh. Also bumped up the time it waits for a new server to start up.
* Added an explicit call to scan-drbd after a new resource is created to ensure that if any calls come after looking for the next free DRBD minor or port, they don't use the ones just used.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Cluster->add_server() to now set failure timeouts to actual numbers instead of INFINITY after discovering that INFINITY doesn't work in those cases.
* Updated Databsae->get_hosts to now check if other entries have the same host name, and if so, to set their host_key to 'DELETED'. This should make it easier to handle when a hardware machine is replaced by new hardware but uses the same host_name.
* Updated Email->check_queue() to start and enable postfix.service if it's found to not be running.
* Updated Get->available_resources() to return '!!no_data!!' when a given host hasn't got any data in scan_lvm_vgs. Now use this in anvil-provision-server to exit if a node or dr host hasn't run scancore yet.
* Fixed a bug in scan-lvm where the pvs_uuid wasn't being loaded properly, preventing lost PVs, VGs and LVs from being flagged as deleted.
* Started work on anvil-migate-server, though it's far from complete.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Removed the exit-if-no-DB check in ocf:alteeve:server so that (hopefully, needs testing), running servers won't be impacted if the nodes lost contact with both/all strikers.
* Updated scan-server to make an explicit check for missing XML definition files on startup and write them if needed.
* Very beginning work on anvil-delete-server has been started.
* Updated anvil-provision-server to wait when it's running in peer mode until the new XML definition is in the DB and then write it out to disk before exiting. Also updated it to add the new server to pacemaker before exiting.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Finished DRBD->get_next_resource() that returns the next available minor and the next free TCP port (with two free ports available after it).
* Created Storage->get_storage_group_details() that pulls together the LVM, storage group members and storage groups into one block of data.
* Made more progress on tools/anvil-provision-server. It now gets up to the point of creating LVs, creating DRBD resource files, loading them, creating metadata and up'ing the resource. It doesn't yet (successfully) force a new resource to primary.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug in scan-drbd that was still looking for the scan_drbd_resource_uuid from the resource config file. Also added a check to see if 'scan-drbd::resource_status' directory exists before trying to read the files in it.
Signed-off-by: Digimer <digimer@alteeve.ca>
ing or create new servers.
* Created Database->insert_or_update_storage_groups() and ->insert_or_update_storage_group_members() to manage the new associated tables. Together, these tables create storage groups and track the VGs that are members of the group.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Started work on Get->available_resources() that will take an 'anvil_uuid' and figure out what resources are still available for use by new servers or that can be added to existing servers.
* Fixed a bug in ScanCore->agent_startup() where tables weren't being generated properly from the agent's SQL file.
* Made Storage->change_mode() return silently if it's called without a mode being passed. This happens frequently and is harmless so it's not worth filling the logs with errors.
* Renamed the 'start_time' key to 'at_start' when recording files' MD5 sums in Storage->record_md5sums and ->check_md5sums.
* When we moved the directory scan logic out of the 'scancore' daemon and into 'Storage->scan_directory', the logic to record scan agent names in 'scancore::agent::<file>' was removed. This broke a few things and, so, it was restored when it was found that a file starts with 'scan-' and the directory matches the scancore agent directory.
* Moved the 'scancore' daemon's 'load_agent_strings' to 'Words'
* Updated Words->parse_banged_string() to look for variables in the format 'value=X:units=Y' and translate it properly.
* Fixed a bug in scan-ipmitool where discovered sensor INSERT SQL queries were queued, but not committed.
* Fixed a bug in scan-storcli where a while loop was broken, preventing execution.
* Fixed a bug in the 'scancore' daemon where it wouldn't exit if sums changed. Fixed a bug where alerts weren't being sent between loops. Fixed a bug where command-line log level wasn't surviving inside the main loop.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Created Database->get_power() that loads data from the special 'power' table.
* Fixed a bug in calls to Network->ping() where some weren't formatted properly for receiving two string variables.
* Updated Database->get_anvils() to record the machine types when recording host information.
* Updated Database->get_hosts_info() to also load the 'host_ipmi' column.
* Updated Database->get_upses() to store the link to the 'power' -> 'power_uuid', when available.
* Created ScanCore->call_scan_agents() that does the work of actually calling scan agents, moving the logic out from the scancore daemon.
* Created ScanCore->check_power() that takes a host and the anvil it is in and returns if it's on batteries or not. If it is, the time on batteries and estimate hold-up time is returned. If not, the highest charge percentage is returned.
* Created ScanCore->post_scan_analysis() that is a wrapper for calling the new ->post_scan_analysis_dr(), ->post_scan_analysis_node() and ->post_scan_analysis_striker(). Of which, _dr and _node are still empty, but _striker is complete.
** ->post_scan_analysis_striker() is complete. It now boots a node after a power loss if the UPSes powering it are OK (at least one has mains power, and the main-powered UPS(es) have reached the minimum charge percentage). If it's thermal, IPMI is called and so long as at least one thermal sensor is found and it/they are all OK, it is booted. For now, M2's thermal reboot delay logic hasn't been replicated, as it added a lot of complexity and didn't prove practically useful.
* Created System->collect_ipmi_data() and moved 'scan_ipmitool's ipmitool call and parse into that method. This was done to allow ScanCore->post_scan_analysis_striker() to also call IPMI on a remote machine during thermal down events without reimplementing the logic.
* Updated scan-ipmitool to only record temperature data for data collected locally. Also renamed 'machine' variables and hash keys to 'host_name' to clarify what is being stored.
* Updated scancore to clear the 'system::stop_reason' variable.
* Added missing packages to striker-manage-install-target.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug in Database->check_agent_data() where the list of tables wasn't passed in, and thus the table list wasn't then passed on to Database->_find_behind_databases().
* Started work on a new method called Storage->parse_lsblk().
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Database->insert_or_update_temperature() to accespt a 'delete' parameter (which, surprise, deletes a record).
* Updated (but not yet tested) the RPM .spec to require that 'core' and the other three packages are required to be the same version.
* Updated scan-ipmitool and scan-storcli scan agents to now delete temperature data belonging to lost sensors.
* Fixed tools/striker-manage-install-target to add multiple missing packages.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Alert->register() to take message variables using the 'variables' parameter.
* Added a 'cache' parameter to Database->insert_or_update_health() and ->insert_or_update_temperature(). When set, the SQL UPDATE/INSERT calls and pushed into the array reference set in 'cache'. This is to allow performance improvements when processing a large amount of sensor/device data.
* Updated Log->variables() to take a 'prefix' parameter that, when set, will prefix the string to each variable line.
* Updated scan-ipmitool to use Database->insert_or_update_health() and ->insert_or_update_temperature().
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug if Get->free_memory() where host_type was still being called from the old System->host_type method.
* Added global support for '--log-secure' and '--log-db' switches to enable logging of secure data and DB transactions, respectively.
* Created Database->get_tables_from_schema() that parses a SQL schema file and returns an array reference of tables found, in the order they were found.
* Updated ScanCore->agent_startup() to no longer require manually defining database tables, using Database->get_tables_from_schema() when not manually set.. Updated all existing agents to use this.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated ScanCore->agent_startup() to use Database->get_tables_from_schema() when the 'tables' parameter isn't passed.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Get->os_type() to work on local and remote hosts.
* Fixed a but in tools/striker-initialize-host where calls to Network->find_matches() where being checked properly for success/failure.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Fixed a bug in Database->insert_or_update_power() where the check to see if 'power_ups_uuid' was passed in was reversed. Also fixed a bug where the convertion of the value to TRUE/FALSE for the old value wasn't being set correctly.
* Updated Server->get_definition() to only translate the host name to a uuid if the host uuid wasn't passed in. Added a sanity check on the UUID as well.
* Cleaned up how existing UPSes are displayed in Striker when managing UPSes. Also renamed the form's scan agents to match the real agent names.
* Fixed alert sorting in scan-apc-pdu.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Finished scan-apc-pdu! Unlike M2, it tracks PDUs without host-binding, and tracks them by their fences entry / scan_apc_pdu_uuid instead of by serial number.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Created (but not finished) scan-apc-pdu
* Added support to tracking maintenance-mode for nodes in Cluster->parse_cib
* Created Remote->read_snmp_oid().
* Created Server->get_definition.
* Updated Server->get_status() to write-out server XML files on-demand.
* Finished scan-cluster.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Renamed scan-storage to scan-lvm as we only really care about LVM data in this agent. A dedicated scan-drbd will be created later. Got the agent to parse the pvs/vgs/lvs data.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated the servers table to remove the 'not null' constraints on the server_start_after_server_uuid, server_pre_migration_file_uuid and server_post_migration_file_uuid columns.
* Updated ScanCore->agent_startup() to connect to the database(s) when there isn't a table list.
* Updated Server->migrate_virsh() to test for DB access before making DB calls (to allow ocf:alteeve:server to function even if all ScanCore DBs are offline).
* Updated ocf:alteeve:server to connect to the databases (though work without it), and changed '$FILE_NAME' to be 'ocf:alteeve:server' (to make logging more legible)
* Created the skeleton for 'scan-storage'.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Renamed servers -> 'server_clean_stop' to 'server_user_stop' to make it clearer what the column represents.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Updated Server->migrate_virsh() to set 'servers' -> 'server_state' to 'migrating' and clear it again once the migation completes. Also added support for cold (frozen) versus live migrations.
* Updated Cluster->parse_cib() to check if a server with the server_state set to 'migrating' isn't actually migrating anymore and, if not, to clear that state. This is needed as scan-server will blindly ignore/skip any migrating server, and if a migration call is interrupted, the state could get stuck.
* Updated the 'servers' database table (and associated Database methods) to add columns for;
** server_ram_in_use - tracking RAM used by a running server
** server_configured_ram - RAM allocated to a running server (used with the above to alert a user and track _currently_ available RAM)
** server_updated_by_user - To be set by Striker tools to indicate when the user made a change that needs to push out to nodes / running server.
** server_boot_time - Tracks the unixtime when the server booted (to track uptime even if the server migrates across nodes).
* Created Get->anvil_name_from_uuid() to easily convert an Anvil! UUID into a name. Also created ->host_uuid_from_name() to translate a host name into a host UUID.
* Created Server->get_runtime() that translates a server name into a process ID and then uses that to determine how long (in seconds) it has been running. This is used when a server transitions from 'shut off' to 'running' to determine exactly when the server booted (current time - runtime).
* Renamed all 'Server->parse_definition' calls that used 'from_memory' to 'from_virsh' to clarify the data source.
* Made scan-hardware smarter about RAM change alerts.
* Updated scancore to load agent strings on startup so that processing pending alerts works properly.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Renamed the 'defitintions' table to 'server_definitions' to clarify the purpose, and made all the 'server' columns have then 'not null' constraint.
* Created Database->insert_or_update_servers(), ->get_servers(), ->insert_or_update_server_definitions() and ->get_server_definitions().
* Updated scancore, anvil-daemon, and scan agents to not run unless they're run with root privs.
* Got scan-server to update the servers / server_definition tables and the on-disk file when needed.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Began (but haven't finished) Database->insert_or_update_servers().
* Created Storage->get_file_stats() to collect the (l)stat information for a file.
* Got more work done on scan-server.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Added support in anvil.conf to disable scan agents with 'scancore::<agent_name>::disable', and added handling this to agents. Also allowed for '--force' to override this setting.
* Updated ScanCore->agent_startup() to allow for empty scan agent table lists.
Signed-off-by: Digimer <digimer@alteeve.ca>
* Did more work on parsing server data out of the CIB. There is still an issue with determining which node currently hosts a resource, however.
* Renamed Server->boot to ->boot_virsh, ->shutdown to ->shutdown_virsh and ->migrate to ->migrate_virsh to clarify that these methods work on the raw virsh calls, outside of pacemaker (indeed, they are what the pacemaker RA uses to do what pacemaker asks).
* Got more work done on the scan-cluster SA.
* Created the empty files for the pending scan-server SA.
Signed-off-by: Digimer <digimer@alteeve.ca>
Digimer
Fabio M. Di Nitto